top of page

How to Diagnose Why Your Pool Heater Pilot Light Keeps Going Out

Nov 7
9 min read

Last Updated: November 6, 2026

Quick Summary

A pool heater pilot light usually goes out because of a gas supply problem, a dirty or clogged pilot assembly, a faulty thermocouple, or airflow and venting issues. Water flow can also matter, since many heaters will not fire if the pressure switch does not close.

  • Turn the heater off and shut off the gas supply before opening any access panel.

  • A pilot that lights and then drops out often points to the thermocouple or a weak flame.

  • Check the filter, skimmer basket, and valves when the pilot lights but the main burner never fires.

  • Never bypass the pressure switch or thermocouple to force ignition.

  • Call a licensed technician if the pilot will not light after two or three attempts.

Pilot light keeps going out?

Air Express HVAC LLC diagnoses and repairs pool heaters of all makes and models.

Table of Contents

How a Pool Heater Pilot Light Works and Why It Fails

A pool heater pilot light is a small, constant flame that ignites the main burner whenever the heater calls for heat. When that pilot goes out, your pool heater cannot warm the water, no matter how the thermostat is set.

Common pilot failures can come from gas supply problems, a dirty or clogged pilot assembly, a faulty thermocouple, or airflow and venting issues. Water flow can also matter, because many heaters will not fire if the pressure switch does not close.

Knowing how the system is built makes the diagnosis much easier. Here is the basic sequence:

  • The gas valve opens and gas flows to the pilot.

  • The igniter or pilot spark lights the pilot flame.

  • The thermocouple senses that flame and holds the gas valve open.

  • The main burner lights once the heater receives a call for heat and water is flowing.

If the pilot will not light, the problem is usually upstream. If it lights and then goes out, the thermocouple or the flame itself is the likely suspect.

Start Here: Safety Checks Before You Touch Anything

Before you open the access panel, turn the heater off at the control and shut off the gas supply at the valve near the unit. Give it a few minutes to cool if it has been running.

Homeowner using a flashlight to inspect a pool heater pilot light panel in a sunny Fort Myers backyard.

Check for the smell of gas. If you smell rotten eggs or gas, leave the area, avoid flicking switches, and call your gas utility or 911 from outside.

Keep these basics in mind:

  • Never bypass the pressure switch or the thermocouple to force ignition.

  • Keep flammable materials and pool chemicals away from the heater.

  • Make sure the area has fresh air for combustion.

  • Stop and call a professional if you are unsure of any step.

Why a Pool Heater Pilot Light Won't Stay Lit

A pilot that lights and then drops out is one of the most common complaints. If yours keeps failing, you can review emergency pool heater repair options available around the clock. In most cases, the pilot flame is not getting the gas or heat it needs to stay on.

Watch for these patterns:

  • The flame is weak, yellow, or flickers. This often points to a dirty pilot orifice or a partly blocked pilot tube.

  • The pilot goes out when you release the reset button. The thermocouple is probably not heating up enough to hold the valve open.

  • The pilot stays lit, but the heater shuts down soon after. A flow or pressure problem may be tripping the safety circuit.

Debris from the pool, such as dirt or spider webs, can clog the small pilot opening. Check the pilot for blockage before you assume a bigger failure.

Pool Heater Thermocouple Problems and How to Spot Them

The thermocouple is a thin metal probe that sits in the pilot flame. It produces a small electrical signal that tells the gas valve the pilot is lit. When it weakens or fails, the gas valve closes as soon as you release the reset knob.

Signs of a bad thermocouple include:

  • The pilot lights, then goes out within seconds of releasing the knob.

  • Soot or corrosion on the probe tip.

  • A loose or damaged connection at the gas valve.

Cleaning the tip and checking the connection is a simple first step. Replacement is often straightforward, but match the part to your heater's make and model. A thermocouple that looks fine can still fail under load, so a technician can test its millivolt output.

Gas Pool Heater Not Lighting: Gas Supply, Air, and Venting Checks

When the pilot will not light at all, work from the supply side inward.

Step 2: Confirm gas is reaching the unit. Check that the manual gas shutoff valve near the heater is fully open (the handle should be parallel to the pipe). If you are unsure whether your unit is correctly matched to your setup, a guide on sizing a pool heater for a screened lanai explains the capacity side.

Step 3: Match the check to your gas type. Natural gas and propane behave differently and use different orifices and manifold pressures.

  • Natural gas: A common pattern is a heater that lights briefly and then drops out when other gas loads (furnace, water heater, range) run at the same time, which points to low or fluctuating supply pressure. Utility-supplied pressure problems are the gas utility's responsibility, not yours.

  • Propane: Check the tank level first. A tank that is nearly empty can still supply enough vapor for a small pilot flame but not enough for the main burner, so the pilot lights and the burner never fires. Cold weather reduces propane vaporization, and an undersized or single-tank setup can starve the heater under demand. Never attempt to adjust a propane regulator yourself.

Step 4: Check combustion air and venting. Gas heaters need unrestricted combustion air and a clear flue.

Step 6: Know where DIY stops. Checking a shutoff valve, a tank level, a filter, and a vent for obstructions is reasonable homeowner work.

Watch out: Relighting the pilot repeatedly without finding the cause can flood the burner compartment with unburned gas.

Natural gas vs. propane: what changes in the diagnosis

Symptom

Natural gas likely cause

Propane likely cause

Pilot lights, burner never fires

Low supply pressure under load

Low tank level or vaporization issue

Pilot lights then drops out

Fluctuating utility pressure

Undersized tank or cold-weather vapor starvation

Weak yellow flame

Dirty orifice or incorrect orifice

Incorrect orifice or regulator fault

A licensed technician should verify the gas type, orifice size, and manifold pressure before any adjustment, because an incorrect orifice for the fuel type can produce dangerous combustion.

Clogged Pilot Parts, Flow Faults, and Error Codes

Clogged pilot parts are easy to overlook. Dirt, pool debris, and corrosion can block the pilot orifice and pilot tube. Carefully clean these parts with a soft brush and compressed air, and never use a sharp wire that could enlarge the opening.

Water flow is a separate issue that mimics a pilot problem. If the filter is dirty, the skimmer basket is full, or a valve is closed, the pressure switch may not close. The heater then never starts, even with a good pilot. Check the filter and pump basket first.

Many modern heaters display error codes. Consult the manual for your model. A code tied to ignition, flame, or pressure usually points to one of the causes above.

Pool Heater Pilot Light Repair in Fort Myers: When to Call a Technician

Fort Myers adds local conditions that generic pilot-light guides do not account for, and they change which causes are most likely. See the full list of heating and pool heating services offered by the business.

Local factors that affect pilot reliability in Fort Myers:

  • Salt air and corrosion. Coastal air accelerates corrosion on the thermocouple, pilot assembly, and gas-valve connections. A thermocouple that looks clean can develop a corroded tip or a compromised connection faster here than in drier climates.

  • Heavy rain and humidity. Rain driven into a vent or flue can wet the pilot assembly and cause repeated dropouts until it dries. High humidity also encourages corrosion and can affect ignition components over time.

  • Wind exposure. Afternoon thunderstorms and seasonal wind gusts can blow back down a flue or push the pilot flame away from the thermocouple. Heaters installed on an exposed pool deck or near a corner where wind eddies are more vulnerable than sheltered units.

  • Outdoor equipment placement. A heater tucked against a fence, under a screen enclosure, or close to dense landscaping may have restricted combustion air or a vent termination that recirculates exhaust. Placement problems often show up as intermittent pilot failures that worsen on hot, still days.

Distinguish the fault category before you call. The symptom tells you which part of the system to investigate, and that determines what a technician will check:

  • Pilot will not light at all: gas supply, pilot orifice, or ignition system.

  • Pilot lights but will not stay lit after releasing the reset: thermocouple or flame sensor.

  • Pilot stays lit but the main burner never fires: water flow, pressure switch, or gas valve.

  • Heater locks out with an error code: control board or safety circuit, often triggered by one of the above.

When to call a technician in Fort Myers:

  • The pilot will not light after basic cleaning, gas-valve, and flow checks.

  • You smell gas or suspect a leak.

  • The thermocouple, igniter, or gas valve needs replacement.

  • Error codes return after you clear the flow path.

  • The heater is installed in a screen enclosure or tight space where venting is questionable.

What affects repair cost in the Fort Myers area. For current pricing, call Air Express HVAC LLC or visit its website for a quote, since costs depend on the parts needed and the work involved.

Because Fort Myers heaters face salt air and storm exposure, an annual inspection before pool season is a practical way to catch corrosion and venting problems before they strand you with a cold pool.

Booking Your Pool Heater Diagnostic with Air Express HVAC

If you have worked through these checks and the pilot still keeps going out, a professional diagnostic will save time. Air Express HVAC LLC provides service for pool heaters, including gas systems, across Southwest Florida. You can read about the company's services and reliability before you schedule.

Air Express is home of the "10 year worry free parts and labor guarantee."

GIVE US A CALL to schedule your pool heater diagnostic today.

Frequently Asked Questions

Why does my pool heater pilot light keep going out?

The most common causes are low gas pressure, a dirty or clogged pilot orifice, a faulty thermocouple that no longer senses the pilot flame, and poor airflow or venting. A thermocouple that fails to hold a signal will shut the gas off within seconds of the pilot lighting. Start by checking that the gas supply is on and the pilot assembly is clean, then inspect the thermocouple. If the problem continues after these checks, a licensed technician should test gas pressure and the safety components before further attempts.

How do I know if a pool heater thermocouple is bad?

A bad thermocouple usually lights the pilot, then the flame goes out as soon as you release the control knob. Look for a pilot flame that is weak, lifting, or not contacting the thermocouple tip. Thermocouples can be tested with a millivolt meter, and a reading that falls well below the manufacturer's specification points to replacement. Because thermocouple replacement is a gas safety repair, have a licensed HVAC technician perform it unless you are qualified to work on gas appliances.

Can a dirty pilot orifice stop a pool heater from lighting?

Yes. A pilot orifice clogged with dust, spider webs, or debris restricts gas flow, producing a weak or absent pilot flame. Carefully inspect the orifice and pilot tube for blockages and clean them with compressed air or a soft brush. Do not enlarge the opening with wire or a drill, since that changes the gas flow and can create a hazard. If the pilot still will not stay lit after cleaning, the problem likely lies elsewhere in the gas or safety system.

When should I call a professional to repair a pool heater pilot light in Fort Myers?

Call a professional if the pilot will not light after basic checks, if it repeatedly goes out, if you smell gas, or if the error code points to a gas valve or ignition fault. Gas valves, thermocouples, and ignition controls require calibrated tools and gas safety knowledge. Air Express HVAC LLC services all brands, makes, and models across Southwest Florida. For current pricing, call the company or visit its website for a quote, since costs depend on the parts needed and the work involved.

 
 
 

Comments


bottom of page